Gray composite panel facade under construction

Mounting System · Concealed Fastening

Male-female composite panel system

Trays that interlock with S- and Z-shaped profiles, creating a consistent horizontal joint. Ideal for horizontal sections and curved facades, with removable trays.

  • Hidden Fastening, Tongue-and-Groove
  • Tray height: Up to 700 mm
  • Length: Up to 6 m
  • 30 mm flange

Male-female

Interlocking joints and concealed fasteners

In the male-female system, each tray has a female profile riveted along its bottom edge and a male profile along its top edge. During installation, the upper tray slots into the one below and is only screwed to the rails through its top profile, so the screws are hidden by the next row and the facade shows a continuous, even horizontal joint.

It is the best option for facades with a horizontal layout, large solid areas and ribbon windows, and one of the systems that adapts best to curved facades, whether concave or convex, because the tray is curved in the workshop. The trays can also be removed and reused. At StarModul we ship the machined trays with their profiles already riveted, numbered and ready to slot together, or install them ourselves if the project is in Catalonia.

  • Fastening: Hidden, tongue-and-groove
  • Tray height: Up to 700 mm
  • Length: Up to 6 m
  • Flange: 30 mm
Building with overhangs clad in gray composite panels

Concealed mounting

How Tongue-and-Groove Works

In the tongue-and-groove system, each tray has a female profile (S) riveted to the bottom and a male profile (Z) riveted to the top. During assembly, the top tray fits into the bottom one and is secured to the uprights via the top profile. This results in a continuous horizontal joint with no visible fasteners.

  • Horizontal trays up to 700 mm high and up to 6 m long.
  • 30-mm flanges riveted to the S and Z profiles, providing high longitudinal rigidity.
  • It allows for curved trays (concave and convex facades).
  • Removable and reusable trays.
Diagram of the male-female composite panel system
Trays nested with S-shaped (bottom) and Z-shaped (top) profiles.

Mounting

Assembly Order

  1. Substructure. Corner brackets anchored to the wall (with insulating shims if you want to break the thermal bridge) and aluminum stiles in T, L, or omega shapes.
  2. Boot profile. It is attached to the base of the facade to support the first row of shelves.
  3. Clearance adjustment screw. It is placed on the starter profile and on each Z-profile, with a maximum spacing of 500 mm between pieces: it prevents vibrations and helps with leveling.
  4. Trays from bottom to top. Each tray rests with its S-profile on the Z-profile of the one below it and is secured to the uprights from above.
  5. Reinforcements. Depending on the height of the tray and the wind conditions in the area, reinforcements are glued to the uprights or a stiffening profile is installed behind the tray.

Construction details

Details of the male-female system

Horizontal cross-section of the tongue-and-groove composite panel system
Horizontal section
Vertical cross-section of the tongue-and-groove composite panel system
Vertical section
Detail of a crown joint with a tongue-and-groove system
Coronation
Close-up of a male-female connection
Startup
Detail of a lintel with a tongue-and-groove system
Lintel

System Specifications

Components and Dimensions of the Male-Female Connector

ElementDetail
Spacers6063 T5 aluminum double-T profile (59 to 254 mm) or U-shaped, with optional insulating spacer.
Stiles6063 T5 aluminum omega profile, attached to the spacer with an M6 × 60/70 mm through-bolt. The first and last anchors must be no more than 250 mm from the ends.
S-Profile (female)6063 T5 aluminum, riveted to the bottom of the tray.
Z-Profile (male)6063 T5 aluminum, riveted at the top. This is the one that screws onto the omega bracket.
Tray30-mm flanges riveted directly to the S and Z profiles, providing longitudinal rigidity.
EPDM GasketPieces approximately 60 mm long that wrap around the head of the Z-profile, spaced no more than 500 mm apart. They prevent noise and help keep the facade flat.
ReinforcementA 200-mm profile segment on each omega bracket where the tray rests, secured with a rivet or screw; the tray is attached to it with adhesive and double-sided tape. Its use depends on the height of the tray and wind conditions.
Rivets4.8 × 15 mm blind rivet, aluminum/stainless steel.
Distance from wall to panel faceFrom 104 to 314 mm, depending on the spacer.
InsulationFrom 30 to 230 mm, with a 30 mm air gap.

When to use it: facades with horizontal patterns, a large amount of solid wall surface, and few openings (or openings arranged in a strip). On facades with many windows, hanging or riveting is usually more practical.

Frequently asked questions

Questions About Male-Female Differences

How tall can the tray be?

Up to 700 mm high and up to 6 m long. For taller trays, a hanging tray is used.

Can curved facades be built?

Yes, it is one of the systems best suited for curved, concave, or convex facades. The tray is curved in the workshop (with short flanges; recommended minimum radius of about 500 mm).

Can the trays be removed?

Yes, they are removable and reusable, which makes repairs or access easier.

Quote for a Tongue-and-Groove Siding Project

We'll send you the machined trays with their profiles, ready for assembly.