Residential building with a white composite panel facade

Composite panel · installation

Ventilated facade systems using composite panels

Four ways to install composite panels on a ventilated facade: suspended track, tongue-and-groove, riveted, and glued. We’ll explain how each one works, its components, and when to use it. We supply the machined panel and the substructure, and assemble them in Catalonia.

  • Systems 4
  • Aluminum Substructure
  • Tire width ≥ 30 mm
  • Installation in Catalonia

Ventilated facade

Four Ways to Secure the Panel

Every composite panel facade we supply follows the same ventilated facade principle: brackets anchored to the wall, vertical aluminum rails, insulation against the wall, a ventilated air gap and, in front, the panel. What changes from one system to another is how the panel is attached to the rails: as hanging or interlocking (male-female) trays with concealed fixings, or as flat panels that are riveted or bonded.

The choice depends on design and budget. Trays require more machining (milling, bending and formed corners) but leave the facade free of visible fixings; flat panels need less machining and are quicker to install. At StarModul we recommend a system based on the facade layout, the openings and the wind exposure of the site, prepare the cutting plan and ship the machined panels together with the substructure, or install them ourselves if the project is in Catalonia.

  • Systems: 4
  • Frame: Aluminum
  • Inner tube: ≥ 30 mm
  • Filmed in Catalonia
Ventilated composite panel facade on a residential building

Ventilated facade

How to Install a Composite Panel Façade

All systems follow the same ventilated facade design: corner brackets anchored to the wall, vertical aluminum mullions, insulation bonded to the wall, an air space of at least 30 mm, and, in front of that, the composite panel. What varies is how the panel is attached to the mullions.

  1. Spacers (corner brackets). Double-T, U-shaped, or angle aluminum profiles, anchored to the wall with a wall plug and screw. There are 14 lengths (ranging from 59 to 254 mm) to accommodate the thickness of the insulation and any wall unevenness, with 15 mm of adjustment. Insulating shims are used to eliminate the thermal bridge.
  2. Vertical studs. 6063 T5 aluminum omega profiles (or a specific 70 × 24.5 mm profile in the glued system), fastened to the spacers with M6 through bolts. The first and last fasteners are spaced no more than 250 mm from the ends. The spacing between them is determined by the wind load calculation.
  3. Insulation and air chamber. The insulation is glued or attached to the wall; in front of it is an air space of 30 mm or more that ventilates the facade.
  4. Composite panel. On hanging or tongue-and-groove trays (concealed fastening) or on flat panels that are riveted or glued.

Comparison

The Four Mounting Systems

SystemMountingPanelWhen to Use It
Hanging Tray (Boot)HiddenTray with tabs and hanging bootsVertical or horizontal configuration; trays over 700 mm high
Male-femaleHiddenTray with tongue-and-groove profilesHorizontal trays up to 700 mm high and 6 m long; accommodates curves
RivetedViewFlat-cut panelThe simplest and most cost-effective to machine; free-form cutting, curved areas
PastedHiddenCut flat panelClean, uncluttered look with no visible fasteners; renovation and new construction

Tray systems require more machining (milling, bending, and corner forming), but they leave the facade free of visible fasteners. Flat-panel systems require less machining and are installed more quickly.

Choose the system

Details of Each System

Measurement

Substructure and Insulation

All systems leave a 30-mm air gap between the insulation and the panel. The spacer is selected based on the thickness of the insulation:

Spacer (mm)597489104119149179209254
Insulation (mm)30506080100120160180230
Distance from the wall to the visible surface of the panel
SystemMinimumMaximumPanel Mounting
Riveted63 mm273 mm5 mm rivet, fixed and sliding points
Hanging tray100 mm310 mmHanging bracket with EPDM + top screw
Male-female104 mm314 mmS and Z profiles + screw on the Z
GluedBy angle separatorElastic adhesive + double-sided tape

All profiles in the substructure are made of 6063 T5 aluminum. The anchor plugs are selected based on pull-out tests conducted on the actual wall.

Things to Keep in Mind

Key Factors for a Successful Installation

  • Expansion: The panel expands 1.3–1.66 mm per meter for every 100 °C difference in temperature. Allow for joints (about 10 mm) and, for riveted joints, use sliding holes.
  • Directionality of the film: The arrows on the protective film must point in the same direction across the entire facade to avoid variations in shade, especially on metallic finishes.
  • Remove the film in a timely manner: no later than one month after installation, in one piece, and at a temperature above 10 °C. If left on longer, the film's adhesive will stick to the panel.
  • Wind Calculations: The spacing between the uprights and the number of fasteners or stiffeners depend on the wind load in the area and the height.
  • Wall anchors: The load-bearing capacity of the anchors is verified by conducting a pull-out test on the actual substrate (concrete, brick, etc.).

Frequently asked questions

Questions About Assembly

Which mounting system is cheaper?

Riveting and gluing, because the panel lies flat and only needs to be cut. Trough systems (suspended and tongue-and-groove) require milling, bending, and shaping each trough, but they conceal the fasteners.

What is the spacing between the studs?

The wind load calculation specifies this. As a reference, for panel-on-stud construction, studs are spaced at a maximum of 60 cm; for large panels with stiffeners, the spacing can reach approximately 1,200 mm, according to the calculation.

Are you installing the facade?

Yes. We supply the machined panel and the substructure, and we assemble them in Catalonia. Outside of Catalonia, we ship the materials to you ready for assembly.

Can composite panels be installed on an existing facade?

Yes, that's standard practice in building renovation: the corner brackets are anchored to the existing facade, and the panel is installed in front of it, with insulation and an air cavity. See how a facade is renovated using composite materials.

What kind of system does your facade need?

Send us your blueprints or photos, and we'll provide you with a system proposal, a bill of materials, and a quote for the pre-machined panel.